Mobula6 2024 V2 ELRS 1S 65mm Brushless FPV Whoop BNF This is the HappyModel Mobula6 2024 V2 ELRS 1S BNF Whoop 65mm – your ticket to exhilarating FPV drone racing! This compact and agile whoop drone packs a punch with its ELRS (ExpressLRS) technology, ensuring lightning-fast response times and rock-solid connectivity. With a 1S battery configuration, it’s perfect for indoor and outdoor flying, offering impressive maneuverability and speed in tight spaces. Measuring just 65mm. The Mobula6 is small enough to navigate through obstacles with ease while delivering thrilling performance. Whether you’re a seasoned racer or a beginner looking for excitement, the Mobula6 2024 ELRS 1S BNF Whoop 65mm is your ultimate companion for FPV fun in 2024! Product Highlights AIO Flight controller with Serial ELRS Receiver and 5.8G Openvtx V2 has the motor connectors Super light 1S 65mm Brushless whoop only 17.7g Equipment with the lightest brushless motors-SE0702 only 1.46gram FX17-B 1/3 CMOS 800TVL Camera awesome footage Smooth and powerful Compatible for 1S Lipo/LIHV BT 2.0 lipo connector Product Information Brand Name: Happymodel Item Name: Mobula6 2024 1S 65mm ultra light micro FPV Whoop Wheelbase: 65mm Size: 81mm*81mm*37mm Weight: 17.7g Option: V1.0 version with SuperX ELRS V1.0 AIO V2.0 version with SuperX ELRS V2.0 AIO The only difference is v2.0 AIO FC comes with motor plug but V1.0 AIO FC is no motor plug. Special Note: The Camera of Mobula6 2024 changed to Runcam Nano7 Camera since Oct 2024 In the box Item Name Qty Mobula6 2024 1S 65mm whoop Drone Frame Canopy 1 SuperX ELRS AIO 5-IN-1 Flight controller 1 SE0702 KV28000 brushless motor 4 Gemfan 1208-3 31mm tri-blade propellers(4cw 4ccw) 1 FX17-B 1/3 CMOS 800TVL camera NTSC 4:3 1 Onboard 5.8G 25mw~400mw VTX 1 Spare canopy 1 Propeller disassemble tool 1 Screw driver 1 Spare parts specifications: Motor Mode: SE0702 KV28000 Configu-ration:9N12P Stator Diamter:7mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ9.5mm*14mm Weight(g):1.46g No.of Cells(Lipo):1S only Propellers Materials: PC Inch: 31mm Pitch: 0.8 in Weight: 0.21g Mount hole diameter: 1mm Flight controller SuperX ELRS AIO 5-IN-1 Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH) ,ESP32-PICO-D4 Sensor:BMI270(SPI connection) Mount hole size: 25.5mm*25.5mm Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Built-in Betaflight OSD(SPI Control) Built-in 5.8G OpenVTX 0mw~400mw (MSP control) Built-in UART ExpressLRS v3.0.0 Built-in voltage meter sensor , voltage meter scale 110 Built-in current meter sensor , current meter scale 1175 V2 version with connectors Onboard 4in1 ESC Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: Bluejay v0.19.2 Default protocol: DSHOT300 Recommend ESC Startup power value to min1100/max1200 Onboard Serial ExpressLRS receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V3.0 RF Frequency: 2.4GHz Antenna : Enameled copper wire antenna Telemetry output Power: <12dBm Receiver protocol: Serial_based CRSF Compatible with ExpressLRS V3.x.x TX Module Could flash single ELRS receiver firmware by Wifi ExpressLRS firmware target: Generic ESP32 2.4Ghz Rx and VTx Onboard 5.8g VTX Firmware version: OPENVTX MSP VTX PIT Mode support Channels:40ch Transmitting Power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v): <650ma (400mw) Antenna connector: U.FL Runcam Nano7 Model:Runcam Nano7 Image Sensor: 1/3″ CMOS Horizontal Resolution: 800TVL D:150° H:120° V:98° Signal System: NTSC Net Weight: 1.9g with cable Dimensions: L14mm*W14mm*H13mm More Information https://yourfpv.co.uk/wp-content/uploads/2024/03/Mobula6-2024-binding.mp4
