$87.75
$123.73
HappyModel Mobula6 2024 V3 ELRS 65mm 1S Race Whoop The HappyModel Mobula6 2024 V3 is simply a 1S Tiny Whoop of 65mm competition, spec made for indoor racing at the highest level and micro freestyle of high, performance. If we exclude the battery, this model weighs only 17. 5g, so it is one of the lightest production whoops in its category, it is designed to be a direct rival of Air65 and other top, notch race, spec 65mm builds. In the center of the V3 lies the new G473 all, in, one flight controller which features an integrated ExpressLRS 2. 4GHz receiver and a 400mW OpenVTX all in one ultra, light board. Equipped with Betaflight 4. 6, this configuration results in very responsive controls, quick gyro movements and clean tuning options for pilots who want to fine, tune their flying. The major V3 highlight is the new Nano5 analog camera. Giving a significantly sharper and clearer picture than the earlier Mobula versions, it deals with indoor LED gates very well and shows a great performance in low light conditions, even after the sun has set. The contrast and sharpness are at a higher level, thus the camera is perfect for race tracks and darker winter days. Power is delivered from 0702 28, 000KV motors turning 31mm tri, blade props, giving both strong punch and quick throttle response while still holding excellent efficiency. On a nice 300mAh 1S pack, you can only expect about 3. 5 minutes of indoor flight depending on how you manage the throttle. In order to keep the weight at competition level, the entire construction has been soldered no motor plugs, no camera connectors. This helps in reducing weight and hence better performance but if you have to do repairs, you will have to solder again. This is a performance, first whoop made for pilots that are comfortable with micro repairs. The quad comes with an A30 battery connector, which is fully compatible with BT2. 0 batteries and this is why running popular 1S packs of your choice will be a breeze. The crash durability is quite good for its weight class, and the bundle features a spare canopy, extra props and other accessories. If you are after the highest performance in the 65mm category, the Mobula6 2024 V3 is the one that will give you race, ready speed, state, of, the, art electronics and excellent analog clarity all in a true sub, 18g platform. Product Highlights Wheelbase: 65mm Weight: 17.56g (without battery) Flight Controller: G473 AIO (Betaflight 4.6) Receiver: Built-in ExpressLRS 2.4GHz VTX: OpenVTX 25–400mW Camera: HappyModel Nano5 (analog) Motors: 0702 28,000KV Props: 31mm tri-blade Battery: 1S A30 (BT2.0 compatible) USB: JST adapter dongle (no onboard USB-C) Product Information Brand Name: Happymodel Item Name:HappyModel Mobula6 2024 V3 – Ultra light micro FPV Whoop Wheelbase: 65mm Size: 81mm*81mm*37mm Weight: 17.6g Receiver option: 2.4GHz ExpressLRS Serial receiver Mobula6 2024 V3 Mobula6 2024 V2 Flight controller CrazybeeG473 SuperX ELRS V2.0 Firmware target Betaflight 4.6 CrazybeeG473 Customized STM32F411 Built-in ExpressLRS receiver Serial ELRS 2.4GHz Serial ELRS 2.4GHz Built-in Dshot ESC 5A 5A Receiver antenna plug Enameled Copper wire Enameled Copper wire Onboard VTX power 25mw~400mw 25mw~400mw Brushless Motor 0702 KV28000 no plug 0702 KV28000 with plug Propeller Gemfan 1208-3 tri-blade Gemfan 1208-3 tri-blade Battery plug A30(compatible with BT2.0) A30(compatible with BT2.0) Frame Mobula6 2024 frame 2.76gram Mobula6 2024 frame 2.76gram Spare Parts Specifications Motor Mode: SE0702 KV28000 no plug version Configu-ration:9N12P Stator Diamter:7mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ9.5mm*14mm Weight(g):1.46g No.of Cells(Lipo):1S only Propellers Materials: PC Inch: 31mm Pitch: 0.8 in Weight: 0.21g Mount hole diameter: 1mm Flight controller MCU: STM32G473CEU6 Gyro: ICM42688P Sensor: Voltage & Current BEC: 5V, Max. 2A UART: UART 1, UART 2, UART 3 (For RX), UART 4(For VTX) BetaFlight OSD: AT7456E ESC: 5A continuous RX: Serial ELRS 2.4GHz RX antenna: Enameled copper wire 31mm length Receiver firmware target: HappyModel EP1/EP2 2.4GHz RX OPENVTX: 5.8GHz 48 channels, Max. 400mW FC firmware target: CRAZYBEEG473 USB port: SH1.0-4Pin Battery connector: A30 Mounting hole size: 25.5mm x 25.5mm Weight: 3.83g without pigtail and vtx antenna Onboard 4in1 ESC Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: Bluejay v0.21 Firmware target: A_X_5_96KHz Default protocol: DSHOT300 DSHOT600 Recommend ESC Startup power value to min1100/max1200 Onboard Serial ExpressLRS receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V3.0 RF Frequency: 2.4GHz Antenna : Enameled copper wire antenna Telemetry output Power: <12dBm Receiver protocol: Serial_based CRSF Compatible with ExpressLRS V3.x.x TX Module Could flash single ELRS receiver firmware by Wifi ExpressLRS firmware target: Generic ESP32 2.4Ghz Rx and VTx Onboard 5.8g VTX OPENVTX Firmware Support firmware upgrade by openvtx configurator Output power: PIT/10/25/100/400 Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz Channel SEL: SmartAudio2.1 Modulation type: FM Operating temperature: -10℃~ 80℃ Antenna port: IPEX1/U.FL Nano5 Camera Image Sensor: 1/3″ CMOS Horizontal Resolution: 1200 TVL Lens: 2.1mm (M10) 155° FOV TV System: NTSC Signal-to-Noise Ratio: >52dB Electronic Shutter: Auto Automatic Gain Control (AGC): Auto Minimum Illumination:
[email protected] Digital Wide Dynamic Range: Auto Power Supply: DC 3-5.5V Current: 110mA@5V
[email protected] House Material: ABS Net Weight: 1.57g (1.0mm plug version) Item Name Qty Mobula6 2024 1S 65mm whoop Drone Frame Canopy 1 CrazybeeG473 AIO 5-IN-1 Flight controller 1 SE0702 KV28000 brushless motor 4 Gemfan 1208-3 31mm tri-blade propellers(4cw 4ccw) 1 HQPROP ultralight whoop prop 1.2×1.1×3(2cw 2ccw) 1 Nano5 1200TVL camera NTSC 4:3 1 Onboard 5.8G 25mw~400mw VTX 1 Spare canopy 1 Propeller disassemble tool 1 Screw driver 1 More Information Default factory dump file for Mobula6 2024 V3 Betaflight 4.6.0
