AOS 5″ V2 HD ELRS 6S BNF Nebula Pro Vista The AOS 5″ V2 HD 6S has been compared to StrangerThings, out of this world and unbelievably good! OK we made that part up, but it sounds about right. �� Exceptional flight performance. Lightweight. Ultra-low vibration. Easy to maintain. This is state-of-the-art FPV V2.0. When I set out to create a bind and fly version of the AOS 5 V2 I had a vision to combine the latest and greatest technology into the ultimate FPV freestyle machine. This is the result. – Chris Rosser, AOS RC Frame The AOS 5 V2 has been designed to deliver the ultimate freestyle flight experience. The unique arm geometry has been refined through topology optimization to deliver maximum strength and stiffness for minimum weight. The same technology is used to optimize aircraft, satellites and race cars. Motors Exhilarating speed, silky smooth flight after flight. iFlight’s XING2 2207 motors provide power and durability with a 7075 Aluminium unibell design, 5mm titanium shaft, Japanese NSK bearings, N52H center slotted arc magnets, and an integrated o-ring for bearing protection. Electronics Blazing fast with less filter delay for a more locked-in flight feel. The F7 flight controller takes maximum advantage of the vibration performance of the frame with a custom filter tune to reduce latency and improve propwash handling. With OSR4 mode enabled in BF4.3 the BMI270 gyro delivers latency and noise performance that matches or exceeds that of the MPU6000. A BLHeli32 ESC smoothly delivers power to the motors and the massive 55A rating ensures the motors will have all the power they could ever need. Product Highlights 32x32mm GoPro mounting holes in top plate with installed press-nuts Designed for up to 5.1 inch props, no props in view Recommended 1000-1300mAh 6S battery ~350g without battery Captive battery straps 220mm wheelbase 6 mm Arms ELECTRONICS // BLITZ Mini F7 Stack (F7 V1.1 55A 4in1 ESC) FC // BLITZ MINI F7 V1.1 (SKU: BF12000) Mount pattern: 20×20 mm / 4mm PCB hole diameter, silicon grommets for M3 screws Smartaudio / IRC Tramp VTX protocol supported Firmware target: IFRC-IFLIGHT_BLITZ_F722 Motor outputs: 4x (SH1.0 connector) Flash: 16MB (Blackbox flash) I2C serial: SDA / SLA pads Dimensions: 30.5×27 mm MCU: STM32 F722 Barometer: DPS310 OSD Chip: AT7456 LED controller: Yes Beeper pad: Yes Gyro: BMI270 Weight: 5g UARTS: 6 Product Link ESC // BLITZ Mini 55A (SKU:BE11376） Supports: DShot DShot150/300/600/MultiShot/ OneShot etc. Mounting Holes: 20*20mm/Φ4mm Target: IFLIGHT_BLITZ_G2 Burst: 60 Amps BEC: NO Supports 2-6S lipo input MCU：G071 Dimension: 35*42mm Current sensor: Yes Firmware: BLHeli 32 Constant: 55 Amps Current rate: 100 BlackBox: 16MB Weight: 11.3g Product Link In the box AOS 5 V2 HD BNF quad 4 x Nazgul F5 – CW propeller 4 x Nazgul F5 CCW (Grey) 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 75mm 1 x Pre-built and Tested AOS 5 V2 HD BNF 1 x iFlight Lipo Strap 20*250mm (Black) 1 x iFlight Lipo Strap 15*250mm (Black) 1 x Nebula Pro Vista HD System More Information All iFlight BNFs are tested before shipment to guarantee the highest quality. If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at Freshdesk.
