MatekSYS ELRS-R24-D 2.4Ghz Receiver This is the MatekSYS ELRS-R24-D 2.4Ghz RX Matek is known for manufacturing high quality electronic components, this is the ELRS-R24-D receiver. ⚠️ Radio Use Notice: Operation of this product must comply with local laws and licence requirements. Users are responsible for safe and legal use. Product Information ELRS-R24-D Specifications ESP8285, SX1280/1281IMLTRT PA/LNA: SE2431L Antenna connector: IPEX MHF 1 RF Frequency: 2.4GHz (2400~2480MHz) Telemetry power: 22.5dbm~23dbm SE2431L RX_gain: 12.5dB Diversity (antenna-switching), default ANT2 Receiver protocol: CRSF Input voltage: 4~9V DC @ 5V pad Power dissipation: 40~45mA(before binding), 70~75mA(binding), 90~95mA(wifi mode) PCB size: 21mm x 15mm Weight: 3g w/ 2x antennas Packing: 1x ELRS-R24-D, 2x IPEX MHF1 Antennas Firmware ExpressLRS MATEK_2400_RX Firmware update via UART or WIFI ELRS-R24-D: enable “USE_DIVERSITY” (checked) when flashing in ExpressLRS configurator Product Guidance “Any ELRS 2.4Ghz receivers can work with any ELRS 2.4Ghz TX Modules, from any manufacturer and even the DIY ones. This is as long as they have the same binding phrase and configuration options (Regulatory Domain, Performance Options and Extra Data).” More details about ExpressLRS, pls check out ExpressLRS wiki Wiring with FC Receiver RX — FC UART_TX for Telemetry Receiver TX — FC UART_RX for Control Receiver 5V — FC 5V or 4v5 Receiver G — FC GND Receiver protocol: Serial-based receiver – CRSF Traditional Binding Receivers have ExpressLRS FW preloaded without BINDING_PHRASE Power on and off your receiver three times Make sure the LED is doing a quick double blink, which indicates the receiver is in bind mode Use the [BIND] button on the Transmitter Lua script, which sends out a binding pulse Receiver will switch to slow blink once it has received binding pulse. Power off and power on receiver again. If the receiver LED switch to solid on from slow blink, it’s bound with your transmitter. Important: If the RX firmware has a bind phrase, the RX will never enter binding mode using the above procedure. It must be flashed without a binding phrase to do traditional binding. Flashing with ESP_NodeMCU-PyFlasher Connect receiver to USB-TTL module(RX-TX, TX-RX, 5V-5V, G-GND) Connect USB to PC while pressing and holding the boot button in. open ESP_NodeMCU-PyFlasher select Serial port of USB-TTL module, load firmware, select “Dual Output(DOUT)” and “Yes.wipes all data“ click “Flash NodeMCU“ after flashing, Power off and power on your receiver, receiver will enter binding mode(quick double blink). Flashing with ELRS configurator MATEK_2400_RX target is supported by ELRS configurator 1.1.0 with fw release 1.2.0 or newer. In the box ELRS-R24-D Receiver 2 x 2.4Ghz Antenna’s More Information ⚠️ Important Note on Radio Use This product uses radio frequencies. Please make sure you use it responsibly and in line with local laws. Some power levels or modes may need a licence to operate legally. Always fly and operate in a way that avoids interference or safety risks. By using this product, you accept responsibility for complying with the rules where you live. For further details, please refer to the UK’s Radio Equipment Regulations 2017 and Electromagnetic Compatibility Regulations 2016. Learn more about ELRS here MatekSYS Website
