$86.85
$117.25
Happymodel Crux3 1S ELRS V3.0 Toothpick BNF This is the Happymodel Crux3 1S ELRS 3″ Toothpick BNF. You will need a ELRS 2.4Ghz transmitter module Product Highlights 40gram 1s brushless Toothpick drone Receiver: ELRS V3 AIO Flight controller with ELRS Receiver and 5.8G VTX CADDX ANT Camera New 1202.5 KV11500 brushless motor Recommend to use 1s 450mah/650mah/660mah/720mah battery Compatible with CaddxFPV Peanut and Insta360 GO2 Carrying Caddxfpv peanut Got 4.5 minutes flying time with 1s 650mah battery Product Information Brand Name: Happymodel Item Name: Crux3 1S ELRS Wheelbase: 115mm Size: 97mmx97mmx35mm (without propellers) Weight: 40g(without battery) Product Manual Happymodel-Crux3-1S-ELRS-V2.0-with-ELRS-2G4-V3.2-manual-document HappyModel Crux3 ELRS Package Item Name Qty Crux3 Frame and canopy 1 ELRS F4 2G4 flight controller built-in SPI ExpressLRS 2.4G receiver 1 Happymodel EX1202.5 KV11500 brushless motor 4 Gemfan 75mm bi-blade Propellers(4cw 4ccw) 1 Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera 1 5.8G 25mw~200mw 40ch vtx (Flight controller built-in) 1 Screw Driver 1 Propeller disassemble tool 1 3D Printed canopy for Insta360 GO2 and CaddxFPV Peanut Happymodel Handbag 1 Motor Mode: EX1202.5 KV11500 Configu-ration:9N12P Stator Diamter:12mm Stator Length:2.5mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ14mm*14.5mm Weight(g):4.4g No.of Cells(Lipo):1S Propellers Gemfan 75mm Center Thickness:5mm Prop Diameter:75mm Center Hole diameter:1.5mm Pitch:0.9in Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Original whoop size compatible Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI ExpressLRS 2.4GHz receiverBuilt-in 5V 1A BECFlight controllerfirmware target: CRAZYBEEF4SX1280 Onboard 4in1 ESC MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_REV16_7.HEX Default protocol: DSHOT300 Battery Connector Type: PH2.0 Onboard SPI ExpressLRS 2.4GHz Receiver Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz RF Frequency: 2.4GHzAntenna : SMD antenna Telemetry output Power: <12dBmReceiver protocol to flight controller: CRSFCould bind with All ExpressLRS 2.4GHz TX module , ExpressLRS firmware need 1.0.0 or latest Onboard 5.8g VTX Output power: 25mw~400mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smart audio ready Caddx ANT 1200tvl camera Image Sensor: 1/3″ CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC or PAL IMAGE: 16:9 or 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination:
[email protected] Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14*14mm(with bracket to 19*19mm) Wide Power Input: DC 3.7-18V Work Temperature: -20℃~ 60℃ Weight: 2g (N.W.) VTX TABLE Update log: The Crux3 1S ELRS v2.0 version comes with ELRS F4 2G4 V3.1 which was built-in OPENVTX could support max 400mw output. Please use following vtxtable # VTX Table # SMARTAUDIO # vtxtable vtxtable bands 6 vtxtable channels 8 vtxtable band 1 BOSCAM_A A FACTORY 5865 5845 5825 5805 5785 5765 5745 5725 vtxtable band 2 BOSCAM_B B FACTORY 5733 5752 5771 5790 5809 5828 5847 5866 vtxtable band 3 BOSCAM_E E FACTORY 5705 5685 5665 0 5885 5905 0 0 vtxtable band 4 FATSHARK F FACTORY 5740 5760 5780 5800 5820 5840 5860 5880 vtxtable band 5 RACEBAND R FACTORY 5658 5695 5732 5769 5806 5843 5880 5917 vtxtable band 6 LOWRACE L FACTORY 5333 5373 5413 5453 5493 5533 5573 5613 vtxtable powerlevels 5 vtxtable powervalues 1 2 14 20 26 vtxtable powerlabels 0 RCE 25 100 400 save
